The Well Installation Form is a part of the standard EDGE format (EDGE_SPM). Default units are obtained from RVF.RT_UNIT.UNIT_CODE, where UNIT_TYPE = length.
Segment material types are obtained from RVF.RT_WELL_SEGMENT_TYPE.MATERIAL_TYPE_CODE. Segments types are predefined, but they can be customized. More information is available in the Associating Well Segment Ref Values with Well Installation Form article.
Note: Hovering over a field in this form will create a tooltip, and the Intelligent Bar will display information about the input and source of the field. |
Section |
Corresponding EDGE Column |
Reference Value |
|---|---|---|
Default Units |
Depth |
RT_UNIT.UNIT_CODE (UNIT_TYPE=Length) |
Diameter |
RT_UNIT.UNIT_CODE |
|
Top of Protective Layer |
Start_Depth |
Numeric Field (15 characters) |
Depth_Unit |
RT_UNIT.UNIT_CODE |
|
Protective Cover Type |
Material_type_code |
RT_WELL_SEGMENT_TYPE.MATERIAL_TYPE_CODE |
Top of Well Riser |
Start_depth |
Numeric Field (15 characters) |
Depth_Unit |
RT_UNIT.UNIT_CODE |
|
Well Cap Type |
Material_type_code |
RT_WELL_SEGMENT_TYPE.MATERIAL_TYPE_CODE |
Top of Fill |
Start_Depth |
Numeric Field (15 characters) |
Depth_Unit |
RT_UNIT.UNIT_CODE |
|
Borehole Diameter |
Inner_diameter/Hole_diameter |
Numeric Field (15 characters) |
Hole_diameter_unit |
Text Field (15 Characters) |
|
Well Riser Type |
Material_type_code |
RT_WELL_SEGMENT_TYPE.MATERIAL_TYPE_CODE |
Top of Bedrock |
Material_type_code |
Numeric Field |
Depth_Unit |
RT_UNIT.UNIT_CODE |
|
Diameter |
Inner_diameter |
Numeric Field |
Diameter_unit |
Text Field (15 Characters) |
|
Fill Type |
Material_type_code |
RT_WELL_SEGMENT_TYPE.MATERIAL_TYPE_CODE |
Top of Seal |
Start_depth |
Numeric Field |
Depth_Unit |
RT_UNIT.UNIT_CODE |
|
Top of Filter |
Start_depth |
Numeric Field |
Depth_Unit |
RT_UNIT.UNIT_CODE |
|
Seal Type |
Material_type_code |
RT_WELL_SEGMENT_TYPE.MATERIAL_TYPE_CODE |
Top of Screen |
Start_depth |
Numeric Field |
Depth_Unit |
RT_UNIT.UNIT_CODE |
|
Filter Pack Type |
Material_type_code |
RT_WELL_SEGMENT_TYPE.MATERIAL_TYPE_CODE |
Screen Type |
Material_type_code |
RT_WELL_SEGMENT_TYPE.MATERIAL_TYPE_CODE |
Slot Size |
Slot_size |
Numeric Field |
Slot_size_unit |
Text Field (15 Characters) |
|
Slot Type |
Slot_type |
Text Field (20 Characters) |
Base of Screen |
Start_depth |
Numeric Field |
Depth_Unit |
RT_UNIT.UNIT_CODE |
|
Diameter |
Inner_diameter |
Numeric Field |
Base of Sump |
End_depth/Start_depth |
Numeric Field |
Depth_Unit |
RT_UNIT.UNIT_CODE |
|
Sump Type |
Material_type_code |
RT_WELL_SEGMENT_TYPE.MATERIAL_TYPE_CODE |
Base of Filter |
Start_depth |
Numeric Field |
Depth_Unit |
RT_UNIT.UNIT_CODE |
|
End Cap Type |
Material_type_code |
RT_WELL_SEGMENT_TYPE.MATERIAL_TYPE_CODE |
Base Backfill |
Material_type_code |
RT_WELL_SEGMENT_TYPE.MATERIAL_TYPE_CODE |
Total Depth |
End_depth/Total_depth |
Numeric Field (calculation) |
Depth_Unit |
RT_UNIT.UNIT_CODE |
The inner diameter of a well can be stored in DT_WELL_SEGMENT.INNER_DIAMETER and the corresponding unit in DT_WELL_SEGMENT.DIAMETER_UNIT.
The SEGMENT_TYPE field is set to SOLID_WELL_RISER in EDGE, however, this can be remapped using the remap tables.